Products

/Products
  • Our high quality Alignment Tool is made from Hard Anodised Aluminium and available in the most popular spline sizes (please contact us if yours is not listed). This tool makes aligning a multi disc clutch a straight forward task. 15mm spigot as standard.
  • Description

    **BACK IN STOCK MID MARCH** PART# CA-DC2-FL APPLICATION:  92-95 CIVIC 94-01 INTEGRA CNC machined billet 6061 T6 front lower spherical bearing control arms. Designed for racing use and has similar strength to oem arms. Due to the ball joint angle correction this allowed us to significantly thicken high stress areas while still having the same arm to rotor clearance as oem. Benefits from increasing caster from the lower arm verses the top arm is you will improve suspension travel by having the upper arm in a more centered oem location which will improve clearance and allow for more travel. BENEFITS:
    • Increases positive caster up to 2 deg ***WILL NOT HAVE ANY NOTICEABLE INCREASE IN STEERING EFFORT***
    • Allows for less negative camber
    • Eliminates the need for traction bars
    • Ball joint angle correction for lower ride
    • Holds precise alignments since sphericals stay true and centered and don’t compress and sag over time.
    • Eliminates suspension deflection and geometry changes under load seen with rubber or urethane bushings.
    • 3.2lbs compared to 6lbs stock
    • Extremely resistant to harsh weather, street and racing conditions
    • Low cost fully rebuildable
    • M10X1.25 threaded sway bar holes for after market sway bars using spherical end links.   **can still use oem sway bar bar mounting locations**
    SPECS:
    • 6061 T6 aluminum
    • 304 stainless steel spacers
    • custom spec 5/8″ com10tss fully stainless spherical bearings
  • Description

    **BACK IN STOCK MID MARCH** PART# CA-EK-FL APPLICATION:  96-2000 Honda Civic  CNC machined billet 6061 T6 front lower spherical bearing control arms. Designed for racing use and has similar strength to oem arms. Due to the ball joint angle correction this allowed us to significantly thicken high stress areas while still having the same arm to rotor clearance as oem. Benefits from increasing caster from the lower arm verses the top arm is you will improve suspension travel by having the upper arm in a more centered oem location which will improve clearance and allow for more travel. BENEFITS:
    • Increases positive caster up to 2 deg ***WILL NOT HAVE ANY NOTICEABLE INCREASE IN STEERING EFFORT***
    • Allows for less negative camber
    • Eliminates the need for traction bars
    • Ball joint angle correction for lower ride
    • Holds precise alignments since sphericals stay true and centered and don’t compress and sag over time.
    • Eliminates suspension deflection and geometry changes under load seen with rubber or urethane bushings.
    • 3.2lbs compared to 6lbs stock
    • Extremely resistant to harsh weather, street and racing conditions
    • Low cost fully rebuildable
    • M10X1.25 threaded sway bar holes for after market sway bars using spherical end links.   **can still use oem sway bar bar mounting locations**
    SPECS:
    • 6061 T6 aluminum
    • 304 stainless steel spacers
    • custom spec 5/8″ com10tss fully stainless spherical bearings
  • CA-DC2-RL

    £330.00 £396.00 Inc VAT

    Description

      APPLICATION:  89-01 Acura Integra,  88-91 Honda CRX,  88-95 Honda Civic Replacing the factory rubber bushing rear lower control arm with the Pro Car Innovations Spherical bearing rear lower control arm effectively helps eliminate issues like sloppy inconsistent handling, alignment changes, rear drift under braking. One of the main features of our arm and most important fix or upgrade to any track car is our shock mounting location design that uses a bronze plain bearing which 100% eliminates all rotational deflection caused from heavier after market sway bars. With our design the rear sway bar will load up instantly with any body roll making the sway bar far more effective. BENEFITS:
    • Bronze bearing shock mount will eliminate 100% of rotational deflection from heavy sway bars
    • Allows for more precise suspension adjustments
    • Helps eliminate wheel alignment changes
    • Helps eliminate suspension deflection seen with rubber or urethane bushings
    • Long lasting maintenance free 4130 steel spherical bearings
    • Extremely resistant to all harsh weather, street and racing conditions
    • Low cost Fully re-buildable
    • M10X1.25 TAPPED SWAY BAR HOLES
    SPECS:  6061 T6 ALUMINUM ARM 304 STAINLESS STEEL SPACERS 5/8″ 4130 OUTER RACE SPHERICAL BEARINGS
  • CA-EGDC-FU-PC

    £365.00 £438.00 Inc VAT

    Description

    **BACK IN STOCK AROUND 2-3-22** Features:
    • Adjustable camber up to 1.5 degrees positive and 2.5 negative over stock OEM arms
    • Offset arm design for 2 degrees more positive caster over the standard arms
    • CNC machined 7075 T6 Aluminum adjustable spherical bearing block
    • CNC machined and heat treated stainless steel high misalignment 45 degree spacers
    • Zinc plated 3/16″ super stiff steel arms
    • Fine thread M10 10.9 grade hardware
    Benefits:
    • Compact design allows factory suspension travel to be retained
    • Improved tire wear when properly adjusted for application
    • Improved cornering, braking and throttle response due to increased stiffness
    • Very stiff 3/16″ steel arms eliminate unwanted arm flex
    • Long lasting, maintenance free and fully rebuild-able
      Application:
    • 92-95 Honda Civic
    • 94-2001 Acura Integra
      Part# CA-EGDC-FU-PC
  • CA-EK-RL

    £330.00 £396.00 Inc VAT

    Description

      PART# CA-EK-RL APPLICATION:  96-2000 Honda Civic Replacing the factory rubber bushing rear lower control arm with the Pro Car Innovations Spherical bearing rear lower control arm effectively helps eliminate issues like sloppy inconsistent handling, alignment changes, rear drift under braking. One of the main features of our arm and most important fix or upgrade to any track car is our shock mounting location design that uses a bronze plain bearing which 100% eliminates all rotational deflection caused from heavier after market sway bars. With our design the rear sway bar will load up instantly with any body roll making the sway bar far more effective. BENEFITS:
    • Bronze bearing shock mount will eliminate 100% of rotational deflection from heavy sway bars
    • Allows for more precise suspension adjustments
    • Helps eliminate wheel alignment changes
    • Helps eliminate suspension deflection seen with rubber or urethane bushings
    • Long lasting maintenance free 4130 steel spherical bearings
    • Extremely resistant to all harsh weather, street and racing conditions
    • Low cost Fully re-buildable
    • M10X1.25 THREADED SWAY BAR MOUNTING HOLES
    SPECS:  6061 T6 ALUMINUM ARM 304 STAINLESS STEEL SPACERS CUSTOM SPEC PCI 5/8″ COM10SST FULL STAINLESS (as of 7-10-2020) SPHERICAL BEARINGS
  • Description

    PRODUCT UPDATE AS OF 10-25-21. WE ADDED A CAM BOLT ADJUSTER TO THE ADJUSTMENT SLOTS FOR EASY CAMBER AJUSTMENTS AND WILL ALSO PREVENT ANY SLIPPING. THE ARMS WILL ALSO BE IN OUR NEW GLOSS METALLIC BLACK.    Application: 02-06 RSX 01-05 CIVIC FEATURES:
    • CNC LASER CUT STEEL BRACKETS
    • CNC MACHINED HIGH MISALIGNMENT STAINLESS STEEL SPACERS
    • HIGH QUALITY SPHERICAL ROD ENDS
    • POWDER COATED
    BENEFITS:
    • 3″ LONGER ARM THAN FACTORY FOR IMPROVED ROLL CENTER MOVEMNT DURING BUMP
    • REDUCES UNDERSTEER AND IMPROVES ROTATION DUE TO LESS ROLL CENTER DROP DURING CORNERING/BODY ROLL
    • ALLOWS FOR MORE PRECISE SUSPENSION ADJUSTMENTS
    • REDUCES WHEEL ALIGNMENT CHANGES
    • ELIMINATES UNWANTED SUSPENSION DEFLECTION
    • LONG LASTING MAINTENANCE FREE
    • FULLY REBUILDABLE
  • Description

      Features:
    • Adjustable camber up to 1.5 degrees positive and 2.5 negative over stock OEM arms
    • CNC machined 7075 T6 Aluminum adjustable spherical bearing block
    • CNC machined and heat treated stainless steel high misalignment 45 degree spacers
    • powder coated 3/16″ steel arms
    • Fine thread M10 10.9 grade hardware
    Benefits:
    • Compact design allows factory suspension travel to be retained
    • Improved tire wear when properly adjusted for application
    • Improved cornering, braking and throttle response due to increased stiffness
    • Very stiff 3/16″ steel arms eliminate unwanted arm flex
    • Long lasting, maintenance free and fully rebuild-able
    Application:
    • 89-’93 integra
      Part# CA-DA-FU
  • Description

      Features:
    • Adjustable camber up to 1.5 degrees positive and 2.5 negative over stock OEM arms
    • CNC machined 7075 T6 Aluminum adjustable spherical bearing block
    • CNC machined and heat treated stainless steel high misalignment 45 degree spacers
    • powder coated 3/16″ steel arms
    • Fine thread M10 10.9 grade hardware
    Benefits:
    • Compact design allows factory suspension travel to be retained
    • Improved tire wear when properly adjusted for application
    • Improved cornering, braking and throttle response due to increased stiffness
    • Very stiff 3/16″ steel arms eliminate unwanted arm flex
    • Long lasting, maintenance free and fully rebuild-able
    Application:
    • 88-’91 Civic
    • ’88-’91 CRX
      Part# CA-CRX-FU
  • Description

    **BACK IN STOCK EARLY TO MID FEBRUARY** Features:
    • Adjustable camber up to 1.5 degrees positive and 2.5 negative over stock OEM arms
    • CNC machined 7075 T6 Aluminum adjustable spherical bearing block
    • CNC machined and heat treated stainless steel high misalignment 45 degree spacers
    • powder coated 3/16″ steel arms
    • Fine thread M10 10.9 grade hardware
    Benefits:
    • Compact design allows factory suspension travel to be retained
    • Improved tire wear when properly adjusted for application
    • Improved cornering, braking and throttle response due to increased stiffness
    • Very stiff 3/16″ steel arms eliminate unwanted arm flex
    • Long lasting, maintenance free and fully rebuild-able
      Application:
    • ’92-’95 Honda Civic
    • ’94-2001 Acura Integra
      Part# CA-EGDC-FU
  • Description

      Features:
    • Adjustable camber up to 1.5 degrees positive and 2.5 negative over stock OEM arms
    • Dual-caster option of +2 degrees over OEM
    • High load 863 bronze bearings with stainless steel offset pins for caster adjustment
    • CNC machined 7075 T6 Aluminum adjustable spherical bearing block
    • CNC machined and heat treated stainless steel high misalignment 45 degree spacers
    • powder coated 3/16″ steel arms
    • Fine thread M10 10.9 grade hardware
    Benefits:
    • Compact design allows factory suspension travel to be retained
    • Improved tire wear when properly adjusted for application
    • Improved cornering, braking and throttle response due to increased stiffness
    • Very stiff 3/16″ steel arms eliminate unwanted arm flex
    • Long lasting, maintenance free and fully rebuild-able
    Application: 
    • 96-’00 Honda Civic
    Part# CA-EK-FU 
  • Honda K20 52mm Throttle Body Kit

    £2,077.50£2,707.50
    SFT Optimum Honda K20 52mm Tapered Throttle Body Kit - Curved 
    • Curved manifold for Transverse Installations
    • Throttle body mounted injectors for improved fuel atomisation aiding torque/power output
    • Billet machined manifold for strength and accuracy
    • Air horn/ram pipe/stack length options
    • Carbon stepped air filter back plate (Kit Option)
    • ITG high flow air filter (Kit Option)
    • Wide spray fuel injectors for optimal performance (Kit Option)
    • Quadrant type throttle cable linkage (Kit Option)
    Designed, Developed and Proven on our 'Works Spec' in house engine, SF-K310.
    Ideal for circuit racing or rally applications for those who demand more than what the conventional plenum and single throttles on the market can deliver.
  • Hydro-Max Rebuild Kit

    £22.50 £27.00 Inc VAT
    Please note, this is for a rebuild kit (only) to suit the PTT Hydro-Max Slave Cylinder/Bearing.
  • Radiused 42mm Bearing

    £64.00 £76.80 Inc VAT
    Competition Release Bearing - 40mm I.D The 42mm Fulcrum point of this bearing optimises the longer release fingers of the PTT Clutch range, therefore reducing the force required to disengage the Clutch, subsequently putting less stress on the engines crank thrust bearing. Recommended for all applications where the release mechanism allows for a 40mm bearing.
  • Description: Rear upper suspension link allows for more precise suspension tuning. Provides adjustable camber of 2.5 degrees, positive or negative. Features:
    • CNC machined 7075 T6 hex Aluminum turnbuckles for increased thread strength.
    • CNC machined stainless steel spacers and shaft.
    • 3 piece precision 4130 steel rod ends
    • Anodized and laser etched logo.
    Benefits:
    • Adjustable camber (+/- 2.5*) over OEM
    • Improves even tire wear and temps.
    • Reduces wheel alignment changes
    • Eliminates unwanted suspension deflection
    • Long lasting and maintenance free rod ends
    • Fully rebuildable
    Will fit: 
    • 88-’91 CRX
    • ’88-’00 Civic
    • ’89-’01 Integra
    MSRP $230 Part# CA-DC2-RU
  • SBD have designed this rod to replace the standard fragile item, it has a bronze small end bush, which replaces the press-fit version. Ideal for use with our piston. These rods have been tested extensively to over 9000rpm on standard crankshaft & over 9500rpm on a steel crankshaft.
    So beware of cheap imitations!
    Weight approx 455g
    Centre to centre length approx 146mm
    This design of rod has several improvements which benefit the engine. There are two vertical grooves on the side of the rod, this directs the oil spray as it exits the big end vertically upwards towards the pin and the crown of the piston,. This has two benefits, it helps to supply lubricant directly to the gudgeon pin also the cool jet of oil to the underside of the crown of the piston helps to reduce the temperature of the piston itself. On the small end, we have repositioned the oil hole which feeds the small end bush. This is because the one at the top which is normally used effectively weakens the rod itself which increases the possibility of breakage when the rod is brought down by the crankshaft. By moving the oil hole to the side of the rod, there is far more material in this area to help maintain its strength.
    Because of the above modifications it is no longer necessary to supply an oil feed through the bearing, even if your bearing still has a hole for the oil jet, it does not reduce its improvement, the hole is simply filled with oil and the pressure in this area is maintained.